By Juarez Contracting & Innovation LLC · Published · Updated
Flat and low-slope roofs are common on San Antonio commercial buildings, apartment complexes and some mid-century modern homes — and they leak differently from pitched roofs. There is no slope to shed water, so a flat roof lives or dies on its seams, its drains and its membrane. A patch works when the membrane is sound and the leak is local. It fails when the roof is telling you it is done.
Here is how to tell which one you have.
Why flat roofs leak in San Antonio
The failure mode here is ponding and drainage, not slope. San Antonio sits in Flash Flood Alley, and extreme rain rates overload gutters, drains and scuppers: the city recorded 9.52 inches on 1 July 2002, its third-rainiest day, and 9.87 inches on 25 May 2013. Standing water finds every weak seam and penetration. Add thermal movement — seams open and close as the membrane expands and contracts through San Antonio's heat — and live-oak leaves clogging drains, and you have the three causes behind most flat-roof leaks we see. Membranes also age: trade sources put realistic life for TPO, PVC, modified bitumen and EPDM at 15 to 25 years here.
How do I find the source of a flat roof leak?
Start inside at the stain and work uphill on the roof above it. Water travels along the deck, so the entry point is often well away from the stain. Inspect in this order: drains and scuppers, seams, penetrations such as vents and skylights, and edge flashing. Look for open seams, blisters, cracked sealant, debris dams at drains and soft spots underfoot that suggest a wet deck. Photograph everything before you touch it — if the leak is storm-related, your insurer will want the record. Our flat roof repair page covers the diagnostic steps we use.
Materials you need to patch a flat roof leak
Match the patch to the membrane. TPO and PVC are heat-welded single-ply membranes and need compatible patch material and, usually, professional welding for a lasting repair. Modified bitumen takes compatible bitumen patch products. EPDM rubber takes EPDM primer and tape or adhesive. Using the wrong product on the wrong membrane is the commonest DIY failure: the patch peels, traps water underneath and makes the repair bigger. Whatever the membrane, the surface must be clean and dry, and the patch must extend well past the damaged area on all sides. If you do not know which membrane you have, do not guess — that is the point to call a roofer.
Step by step: how to patch a flat roof leak
- Clear the area. Remove debris, leaves and standing water around the suspect seam or penetration, and let the surface dry.
- Cut out loose material. Remove blistered or delaminated membrane back to sound material.
- Clean and prime. Clean the area and apply the primer or adhesive the membrane manufacturer specifies for that product.
- Apply the patch. Centre it over the damage, extend it well past the edges, and roll or press it firmly to remove air.
- Seal the edges. Seal patch edges and lap seams with the compatible sealant, and check the nearest drain is clear.
- Watch it through the next rain. A patch that holds through one heavy rain is a good sign; one that lifts was the wrong material or a wet surface.
Never patch a roof you cannot reach safely, and never walk a wet flat roof — a wet membrane is slick, and a soft deck can give way.
What causes flat roof leaks in San Antonio?
Beyond seams and drains, check the details: flashing at parapets and walls, pitch pockets around pipes, skylight curbs, and rooftop equipment curbs. In the King William Historic District and other historic districts, contemporary roofing materials are allowed on flat or gently sloping roofs not visible from the public right-of-way — but any exterior work still needs a Certificate of Appropriateness in addition to a building permit.
Common mistakes to avoid
- Patching over a wet surface. The patch will not bond, and trapped water rots the deck.
- Mixing incompatible products. The wrong patch on the wrong membrane peels within weeks.
- Ignoring the drain. A patched seam above a clogged drain will leak again at the next storm.
- Patching a roof that needs replacement. Multiple failing seams on a 20-year-old membrane are a replacement conversation, not a patching one.
When to call a professional
Call when the membrane is past its realistic life, when seams are failing in several places, when ponding returns after every rain, when the deck feels soft, or when you cannot identify the membrane type. Our flat roof installation and flat roof repair teams handle membrane identification, seam work and drainage correction, and we give you a written scope before work starts. More guidance is in our San Antonio roofing blog.
For a flat-roof leak, call Juarez Contracting & Innovation LLC at (254) 329-0299 during business hours and we will check the seams and drainage. We serve homeowners in the San Antonio areas we cover.